Resin-Bound Driveways
Resin-Bound Driveways in Hampshire
Heavy-duty, SUDS-compliant resin driveways engineered for maximum drainage with zero loose stones.
Covering Totton, Southampton, Romsey, Winchester and the New Forest.
- 250-300mm Dig Out
- MOT Type 3 Base
- 60mm Binder Course
Our Installation Process
Engineered from the Ground Up to Prevent Sinking and Puddles
A resin surface is only as strong as the ground beneath it. We do not cut corners. Here is the exact step-by-step engineering standard we use to build every resin driveway.
- 1. Excavation & Edging We dig out 250mm to 300mm depending on ground conditions. We then secure the perimeter using concrete kerbs or metal block borders to contain the liquid resin.
- 2. Membrane & MOT Type 3 Sub-Base A geotextile membrane goes down to stop weed growth and soil shifting. We then pour and mechanically compact 150mm to 200mm of MOT Type 3 aggregate for maximum water drainage.
- 3. 60mm Solid Binder Course We lay a 60mm porous tarmac or concrete base. This acts as the rock-solid, load-bearing layer. We clean and dry it thoroughly before applying any resin.
- 4. Precision Resin Mixing We mix a UV-stable two-part polyurethane resin, then combine it with kiln-dried stone inside a forced-action mixer until every single piece of aggregate is fully coated.
- 5. Hand-Troweled Finish The mixture is tipped, raked, and hand-troweled flat to a precise 15mm to 20mm thickness. It cures enough to walk on in 8 hours and is fully ready to drive on in 48 hours.
Surface Containment & Finishing
Structural Edging, Seamless Junctions and UV-Stable Blends
A lasting resin driveway isn't just about how it looks; it is entirely dependent on how the liquid surface is contained before it cures. We integrate your chosen stone blend with heavy-duty structural borders that actively hold the 15-20mm resin layer in place, preventing edge cracking and surface failure.
- UV-Stable Stone Blends We use a forced-action mixer to combine your chosen natural stone with UV-stable resin. This guarantees consistent, even stone coverage and stops the driveway from suffering patchy yellowing under direct sunlight.
- Structural Perimeter Edging Resin must be physically contained to maintain its structural integrity. Before pouring, we lock in a solid perimeter using heavy-duty concrete kerbs or block paving to act as a rigid barrier that stops the edges from crumbling.
- Precision Hand-Troweled Junctions A machine cannot finish edges properly. We meticulously hand-trowel the resin mixture directly up to your garage thresholds, drainage channels, and boundary walls to create a completely flat, seamless junction with zero trip hazards.
Our Installation Standard
How We Build a Resin-Bound Driveway
A resin driveway is only as strong as the ground beneath it. We build every installation from the sub-base up, ensuring it can handle heavy vehicles, drains perfectly, and never sinks.
- 01 Excavation & Porous Base We excavate 250-300mm of the existing ground. After laying a geotextile membrane to stop weed growth, we compact 150-200mm of MOT Type 3 aggregate to guarantee maximum water drainage.
- 02 Binder Course & Edging To contain the liquid resin, we lock in the perimeter using concrete kerbs or block paving. We then lay a 60mm porous tarmac or concrete binder course to act as a rock-solid, load-bearing layer.
- 03 Mixing & Hand-Troweling We mix UV-stable resin with kiln-dried stone in a forced-action mixer. The mix is hand-troweled to a completely flat 15-20mm thickness. It is walkable in 8 hours and ready to drive on in 48.
Every driveway is priced after a full site survey to assess the exact excavation depth and drainage requirements needed for your specific ground conditions.
Resin Driveway FAQs
Common Questions About Resin-Bound Driveways
We build resin driveways to strict engineering standards. These answers cover our exact specifications for drainage, base preparation, UV stability, and curing times.
How long does a full resin driveway installation take?
A proper installation requires excavating 250-300mm of ground, laying and compacting an MOT Type 3 sub-base, and pouring a 60mm binder course before the resin is even mixed. Depending on the size of your driveway, a full engineered dig-out and build typically takes 5 to 7 days.
Will a resin-bound driveway get puddles?
Not when built correctly. We use 150-200mm of MOT Type 3 aggregate and a 60mm porous binder course. This creates a fully permeable, SUDS-compliant system where rainwater drains straight through the surface into the ground, completely eliminating puddles.
Does resin-bound surfacing have loose stones?
No. We use a forced-action mixer to ensure every single piece of natural stone is fully coated in polyurethane resin. It is then hand-troweled into a solid, seamless 15-20mm layer, meaning no stones will ever kick up or drag into your house.
Will the resin turn yellow in the sun?
We exclusively use high-grade, 100% UV-stable resin. This protects the natural colour of the stone and guarantees the surface will not suffer from the patchy yellowing or degradation seen on cheaper, non-UV installations.
What goes underneath the resin surface?
A resin driveway is only as strong as its base. We dig out the existing ground, lay a weed-proof geotextile membrane, compact 150-200mm of porous MOT Type 3 sub-base, and finish with a 60mm solid binder course. This heavy-duty structure prevents the driveway from ever sinking or cracking.
How long before a resin driveway can be driven on?
Once the resin is hand-troweled to its final 15-20mm thickness, it needs time to set. The surface is safe to walk on after just 8 hours, but you must wait a full 48 hours before parking or driving vehicles on it.
Ready for a driveway built to proper engineering standards? Fill out the form below to book a full site survey.